Report item
Item specifics
Product Description

 

 

 

 

Dear customer, this is the procedure of the screen disassembly we made for the customer, it\'s not for sale, so please don\'t place order , Thank you for your cooperation.

 

Step 1  Pentalobe Screws

Power off your iPhone before beginning disassembly.

Remove the two 3.6 mm Pentalobe screws next to the Lightning connector.

01

 

Step 2  iSclack Opening Procedure 

The next three steps demonstrate using the iSclack, a great tool for safely opening the iPhone 6 that we recommend for anyone doing more than one repair. If you aren\'t using the iSclack, skip to Step 5.

If the plastic depth gauge is attached at the center of the iSclack, remove it now—it\'s not needed for larger phones like the iPhone 6.

Close the handle on the iSclack, opening the suction-cup jaws.

02

 

Step 3

Place the bottom of your iPhone in between the suction cups.

Position the iSclack\'s upper suction cup against the display, just above (but not covering) the home button.

Open the handles to close the jaws of the iSclack. Center the suction cups and press them firmly onto the top and bottom of the iPhone.

03

 

Step 4

Hold onto your iPhone securely and close the handle of the iSclack to separate the suction cups, pulling the front panel up from the rear case.

The iSclack is designed to safely open your iPhone just enough to separate the pieces, but not enough to damage the display cables.

Peel the two suction cups off your iPhone.

Skip the next three steps and continue on Step 8

04

 

Step 5  Front Panel Assembly

If you don\'t have an iSclack, use a single suction cup to lift the front panel:

Press a suction cup onto the screen, just above the home button.

Be sure the cup is pressed securely onto the screen to get a tight seal.

05

 

Step 6

While holding the iPhone down with one hand, pull up on the suction cup to slightly separate the front panel assembly from the rear case.

Take your time and apply firm, constant force. The display assembly is a much tighter fit than most devices.

Using a plastic opening tool, begin to gently pry the rear case down, away from the display assembly, while continuing to pull up with the suction cup.

There are several clips holding the front panel assembly to the rear case, so you may need to use a combination of the suction cup and plastic opening tool to free the front panel assembly.

06

 

Step 7

Pull the plastic nub to release the vacuum seal on the suction cup.

Remove the suction cup from the display assembly.

07

 

 

Step 8

Pull the home button end of the front panel assembly away from the rear case, using the top of the phone as a hinge.

Keep the front panel supported at a 90º angle in relation to the rear case until you remove it—allowing it to fall flat will strain the display cables and their connections on the logic board.

08

 

Step 9

Several clips along the top edge of the front panel form a partial hinge, allowing the front panel assembly to swing open like a book.

During reassembly, align the clips just below the top edge of the rear case. Then, slide the front panel upward until its top edge is flush with that of the rear case.

09

 

Step 10

Remove the following five Phillips screws securing the front panel assembly cable bracket:

Three 1.2 mm screws

One 1.7 mm screw

One 3.1 mm screw

 

10

 

Step 11

Remove the front panel assembly cable bracket from the logic board.

 

11 11

 

Step 12

In the next four steps, take care to pry up onlyon the cable connectors, and not on their sockets on the logic board.

Use the flat end of a spudger to disconnect the front-facing camera and sensor cable connector.

12 12

 

Step 13

Use the flat end of a spudger to disconnect the home button cable connector.

13

 

Step 14

Use the flat end of a spudger to disconnect the display data cable connector.

When reassembling your phone, the display data cable may pop off its connector. This can result in white lines or a blank screen when powering your phone back on. If that happens, simply reconnect the cable and power cycle your phone. The best way to power cycle your phone is to disconnect and reconnect the battery connector.

14

 

Step 15

Use the flat end of a spudger to disconnect the digitizer cable connector.

15

 

Step 16

Remove the front panel assembly from the rear case.

16

 

Step 17  Earpiece Speaker

Remove the following Phillips #00 screws from the earpiece speaker/front-facing camera bracket:

One 2.3 mm screw

One 3.0 mm screw

One 2.2 mm screw

17

 

Step 18

Remove the earpiece speaker/front-facing camera bracket from the front panel.

 

18

 

Step 19

Lift the front-facing camera out of its recess in the front panel.

 

19

 

Step 20

Holding the front-facing camera out of the way, remove the earpiece speaker from the front panel.

Be careful not to touch any of the contacts on the speaker or the cable, oils can damage them and interrupt the connection.

20

 

Step 21  Front Facing Camera and Sensor Cable

Keeping the front-facing camera out of the way, use the point of a spudger to push the ambient-light sensor up out of its recess in the front panel.

21

 

Step 22

Fold the front-facing camera and sensor cable up to allow access to the microphone.

22

 

Step 23

Carefully pry the microphone end of the sensor cable off of the adhesive holding it to the front panel.

 

23

 

Step 24

Remove the front-facing camera and sensor cable from the front panel.

24

 

Step 25  Home Button

Remove the two 1.9 mm Phillips #00 screws securing the home button bracket.

25

 

Step 26

Remove the home button bracket from the front panel.

26

 

Step 27

Use the point of a spudger to disconnect the home button cable connector by pushing it up and away from the home button.

27

 

Step 28

Gently push the top left corner of the home button up away from the front panel.

Do not push the home button all the way through—you only need to get a corner free so that you can pry it free with a spudger.

This membrane is very thin. If you feel like you\'re going to tear the button, apply mild heat (with an iOpener, heat gun, or hair dryer) and try again.

 

28

 

Step 29  

Peel the home button the rest of the way off of the display by prying gently with a spudger.

29

 

Step 30

Use the point of a spudger to carefully separate the home button cable from the adhesive securing it to the front panel.

30

 

Step 31

Once all the adhesive has been separated, remove the home button from the front panel.

31

 

Step 32  Front Panel

Remove the following Phillips #00 screws securing the LCD shield plate to the front panel:

One 1.7 mm screw

Six 1.6 mm screws (three on each side)

 

32

 

Step 33

Lift the front-facing camera end of the LCD shield plate up slightly.

Do not attempt to remove the shield plate entirely, it is still attached to the front panel by the adhered-down home button cable.

 

33

 

Step 34

Slide the point of a spudger behind the shield plate to gently peel the home button cable up off of the front panel.

The home button cable is very thin, go slowly and be careful not to rip it.

Remove the LCD shield plate.

 

34

 

 

 

 

 

 

 

 

 

 

 

    

  

 

1(3)

1. China Post Ordinary Small Packet Plus, free shipping, can be only tracked in China but no detail tracking information in your country.
 
2. When the delivery date will be end and you still not receive your parcel,please contact us and we will extend the delivery time 10-25 days.
 
3. If you want the registered shipping method, please select China Post Air Mail which cost $2.
 
 
 

If the unlucky event that you receive the product, that is shipped not as described or your product is damaged in the shipping, please contact us as soon as possible to arrange return.

1. The products we produce are of highest quality, so if you are not happy with an item you have purchased, please contact our Customer Service Team at Trademanagerr cn1001727048 as soon as possible. We will be able to assist you with anyreturns and refunds based on the condition of the item.

2. If the goods you received not as described. Please in inform us and send us back within 3 days for refund. We will refund of resending within a week from the receipt of the return goods.

3. We offer 12 months warranty for all of our products. All items must be returned in their original condition (With our warrantysticker, LCD with Screen protector, original packing). We strongly advice our customers to test the products first beforeinstallation.A return will only be valid and a refund processed AFTER we have received your items. Buyer is responsible for the return shipping

Packaging Details
  • Unit Type: piece
  • Package Weight: 0.15kg (0.33lb.)
  • Package Size: 40cm x 40cm x 30cm (15.75in x 15.75in x 11.81in)
Shipping
Calculate your shipping cost by country/region and quantity.
Quantity: Ship to:
Packaging Details
  • Unit Type: piece
  • Package Weight: 0.15kg (0.33lb.)
  • Package Size: 40cm x 40cm x 30cm (15.75in x 15.75in x 11.81in)
Payment
We support the following payment methods. All payments made on AliExpress are processed by Alipay.